Functional Fit Requirements for CNC Bushings and Locating Pins

A useful RFQ for a precision bushing or locating pin defines both sides of each important interface. Identify the part to be supplied, the mating hole or shaft, the required assembly function, and the drawing requirements that control size and alignment. A nominal diameter and the instruction “make it fit” leave essential decisions unresolved.

This matters when a bushing mounts in a housing but guides a different component through its bore, or when a pin has one diameter for mounting and another for locating. Each interface can have a different function. Treating them as a single “precision fit” makes quotations difficult to compare and can conceal unanswered design questions.

Map the functional interfaces before requesting a quote

Begin with what the part must do: remain fixed in a housing, locate a removable component, support guided movement, or establish an axial stop. Describe the intended movement and retention without asking the supplier to infer a fit class.

For a bushing, distinguish its outside mounting surface from its working bore. For a locating pin, distinguish its mounting shank from the surface that locates the mating part. A shoulder may establish a seating position while a separate feature retains the component.

InterfaceInformation the RFQ should identify
Bushing outside diameter to housingHousing reference, mounting length, retention arrangement and specified size requirements for both parts
Bushing bore to mating pin or shaftCounterpart reference, working length, intended movement and specified mating dimensions
Pin locating surface to mating holeLocating geometry, engagement length, required fit and any orientation requirement
Shoulder or end face to seating surfaceAxial position, contact surface, clearance to nearby features and drawing-defined geometric relationships

An assembly section often communicates these relationships better than a loose-part photograph. Mark which components are new and which remain in service. If two mating parts are being quoted together, state whether they must remain interchangeable with other parts or are intended only for use as an identified pair. Do not leave that distinction implicit.

Separate dimensional requirements from geometric requirements

A diameter requirement answers a size question. It does not, by itself, fully describe where that feature must be, which way it must point, or how its surface must depart from the intended form.

Consider a flanged bushing. The drawing may need to address its bore size, the relationship of the bore to the outside mounting surface, and the seating face. Tightening the bore diameter alone is not a substitute for defining those relationships.

For a locating pin, the corresponding questions include:

  • What sizes apply to the mounting and locating portions?
  • What form or orientation requirements apply to the functional surfaces?
  • Where must the locating feature be relative to the specified reference features?
  • Which face establishes the installed axial position?

Size and geometry are related specifications, not interchangeable labels. Their interaction depends on the governing drawing rules and any applicable modifiers. A general instruction such as “high concentricity” should be clarified into the intended characteristic, reference and acceptance requirement rather than converted into a guessed numerical value.

Use the standards for the questions they actually address

ISO 286-1:2010 provides the ISO code system for tolerances on linear sizes of cylindrical features and two parallel opposite surfaces. It also explains fit terminology without orientation and location constraints. It does not select the appropriate hole-and-shaft combination for a particular assembly.

Where a drawing uses an ISO fit designation, retain the nominal size, complete designation and applicable reference. ISO also lists a 2013 technical corrigendum for that edition. Identify the controlling references rather than silently changing a legacy requirement.

ISO 1101:2017 addresses the language and interpretation of geometric specifications, including form, orientation, location and run-out. It is not a general supplier accuracy rating or a replacement for specifying the required dimensions.

ISO 5459:2024 addresses datums and datum systems. Its public scope distinguishes defining a datum from the verification method. Naming a datum therefore does not specify a particular measuring machine or inspection procedure.

Keep the drawing’s governing system and edition visible. Do not combine conventions from different systems without an agreed interpretation. If the fit designation, geometric callout or reference scheme is incomplete, ask the responsible design authority to resolve it before production approval.

Identify the locating surfaces and datum requirements

Explain which surfaces locate, support and seat the component in the assembly. Preserve the datum identifiers, their order and the associated requirements shown in the controlled definition. A convenient machining setup or an easily accessible face is not automatically the design datum.

For a bushing, ask whether the functional relationship is between the bore and outside mounting surface, the bore and seating face, or another assembly feature. For a pin, identify the relationship between the locating portion, mounting portion and shoulder where the design requires it.

Not every surface needs a datum label, and not every geometric control uses a datum. The aim is to communicate the actual functional references, not add symbols to every feature.

Locating geometry also matters. Carr Lane’s locating-pin technical guide describes relieved diamond pins whose contact areas must be oriented for their intended locating role. This is a configuration-specific example of why a pin’s shape and orientation can matter beyond its nominal diameter, not a recommendation to redesign an existing fixture.

State whether acceptance applies before or after installation

Clarify whether the requested dimensions apply to the finished loose component, the installed component, or both. If an assembled condition matters, identify the housing, mating parts and installation conditions, and agree who is responsible for assembly and verification.

Carr Lane’s drill-bushing installation guidance warns that excessive interference can distort a press-fit bushing or jig plate, with thin-walled bushings more susceptible. That example shows why installation conditions can matter; its recommended dimensions are not universal values for custom CNC bushings.

State the required material condition, surface finish and treatment from the drawing. Where relevant, identify whether dimensions must be achieved after the specified finishing or treatment. Do not assume that a coating, material change or altered mounting fit leaves the other interface unchanged.

The RFQ should define the finished requirement and constraints. A particular machining sequence or inspection method should be specified only where required or agreed, rather than inferred from another supplier’s catalog.

Record the condition of parts that will remain

Replacement enquiries need more than the dimensions of the new component. Identify the retained housing, mating pin, bushing or fixture, together with the available drawing references and condition information.

Keep three kinds of information separate:

  • The original design requirement.
  • Measurements of the used part or retained assembly.
  • A proposed change to restore or alter function.

A measurement from a worn bore is evidence of its present condition, not automatically the correct nominal size for a replacement. Photos can help identify scoring, damage or orientation, but they do not establish all dimensional requirements.

If the retained interface is unconfirmed, mark it as an open item. Do not request an oversize or undersize replacement as an automatic remedy. Repair dimensions and any change to the original fit need an agreed engineering basis.

Send a controlled drawing and assembly package

Include the part reference, revision, units and quantity. Supply the drawing and available model, and state which data define the requirement if the files disagree.

ISO 16792:2021 recognizes model-only and model-plus-drawing methods of digital product definition. The practical RFQ question is whether the submitted files carry the necessary requirements, not whether one file format is always sufficient. Confirm that dimensions, annotations and referenced notes are accessible in the actual files sent.

Add an assembly view or relevant detail showing the functional interfaces. Include mating-part drawings where available, and distinguish controlled requirements from supporting measurements or photographs.

Use the existing general RFQ guide for the broader purchasing package. If the component also has a threaded feature, use the CNC threaded-parts guide for thread callouts and usable depth; thread requirements do not replace the locating-fit specification.

Use a functional fit RFQ checklist

Complete the information relevant to the part. An unresolved item can be flagged for review rather than filled with an assumed value.

RFQ itemInformation to provide
Part and scopePart reference, revision, quantity, and whether the request covers one component or mating parts
Assembly functionFixed mounting, removable location, guided movement or another defined function
Each mating interfaceNew-part feature, counterpart reference, mating dimensions and engagement or mounting length
Size requirementsNominal dimensions, limits or drawing-specified classes, units and governing references
Geometric requirementsApplicable form, orientation, location or run-out callouts and associated references
Seating and datumsFunctional seating faces, datum identifiers and the required relationships shown on the drawing
Retained partsWhat stays in service, available specifications, measurements and known wear or modification
Condition at acceptanceLoose or installed condition; applicable material, finish and treatment requirements
Verification needsCritical characteristics and any required checking conditions or evidence to agree before ordering
Supporting filesControlled drawing or model, relevant assembly view, and mating-part information where available
Open decisionsUnconfirmed fits, conflicting revisions, missing references, proposed changes and the buyer’s approval contact

These details help suppliers quote the same requirement. They do not replace the buyer’s responsibility to approve the functional specification, and they do not make every item a mandatory website field.

Apply the checklist to common purchasing situations

The following examples illustrate enquiry preparation, not customer case histories or pre-approved supply configurations.

A replacement bushing in an existing housing. Identify the outside mounting interface and internal working interface separately. Send the housing reference, mating-pin information and seating arrangement. State whether the housing and pin will remain, and whether acceptance concerns the loose bushing or the installed assembly.

A stepped locating pin. Distinguish the mounting shank, locating portion and shoulder. Include the mating-hole requirement and the relationship of the locating portion to the mounting feature. If the existing design has reliefs or directional locating surfaces, preserve their references and orientation in the enquiry.

A proposed change to an existing component. Keep the original drawing visible and identify the requested change separately. Ask for manufacturability review against the proposed requirement; do not treat a new material, finish or fit as an approved equivalent before the buyer resolves its effect on the assembly.

Buyer FAQs

Is matching the nominal hole and shaft diameter enough?

No. Identify the permitted size variation for both parts and the other requirements needed for the intended assembly. The same nominal size does not establish the required fit or complete compatibility.

Does a fit designation also control axis location and seating?

Not by itself. Retain the drawing-defined size requirements and separately identify the applicable geometric and seating requirements. Their interpretation follows the governing specification and any modifiers.

Must every geometric tolerance reference a datum?

No. The need for a datum depends on the characteristic being controlled. Preserve the design’s actual callouts and references rather than attaching an arbitrary datum to every surface.

Can the existing housing or mating pin be reused?

That requires review of its specification and condition against the proposed replacement. Identify what will remain, provide available evidence, and flag missing interface information. Reuse is not established by a similar-looking part or matching nominal diameter.

Can I submit a model without a complete drawing?

You can start an enquiry with the available definition, but identify missing requirements. The agreed data set must communicate the critical dimensions, geometric relationships, references and acceptance conditions before production approval.

What if the required fit has not been selected?

Describe the intended function and provide the available mating and assembly information. HESENT can review the drawing-based requirement and manufacturability. The responsible design authority must confirm unresolved fit and functional requirements; a quote should identify assumptions rather than turn them into approved values.

Request a drawing-based component review

HESENT reviews drawing-based enquiries for CNC precision components, including pins, bushings and sleeves. Feasibility and supply scope are confirmed against the submitted requirements.

Request a quote with the part reference or drawing, revision, quantity and the interfaces that matter. Tell us whether you need a quote to an approved drawing, a replacement retaining existing parts, or review of a proposed requirement change.

If available, include the model, mating-part drawings, an assembly section, photos and clearly identified measurements. Flag unresolved fits, datum relationships or acceptance conditions. The website accepts PDF, DWG, STEP/STP, JPG and PNG.